Sunday, November 29, 2020

November 2020: More Tropical Wx & Boat Stuff

 Foreword:  In 1787 Thomas Jefferson wrote to James Madison that “a little rebellion now and then is a good thing.”  To date the USA has experienced two.  The first created our constitution & the republic, with 25,000 American lives lost.  The second in the 1860’s nearly ripped the country apart, took 655,000 souls, and failed.  Those now trying for a third will lose, too, but there will still be a cost.

The Drunken Path of a Confusing Storm
What was once Hurricane Eta morphed into a tropical storm after clobbering Nicaragua and the Honduras as a Cat-4 storm, then plowed into Cuba and eventually made two separate landfalls in Florida.  It had a couple of shots at Fort Myers and missed both times, although not by much.  Its path was as convoluted as it gets, giving the forecasters fits.  And that meant Ghost Rider had to be prepped for a possible Eta fly-by.

We had already deployed extra lines and fenders, so this time our preps were focused on securing canvas on the boat deck and flybridge, lowering antennae, and stowing all loose gear on the main deck into the lazarette.  On the night of 08-November Eta passed about 80 miles to our south, bringing rain and occasional gusts to 45.  After heading west into the Gulf of Mexico, then bending south before turning back to the northeast, Eta cruised past us again on 11-November, this time as a Cat-1 hurricane about 80 miles to our west.  That brought us another round of rain and wind, with gusts up to 60 MPH, and an extra four feet of sea surge.  It was an annoying way to celebrate our Veterans Day. 

Flybridge Cover Taped Down, Bimini Rolled Up & Non-fixed
Antennae Lowered & Tied for Storm Preps

By the morning of 12-November Eta had made its fourth landfall just north of Tampa as it turned to the northeast, and proceeded to strafe the coastlines of Georgia and the Carolinas before continuing out to sea a few days later.  We spent a day putting Ghost Rider’s gear back to a normal state, hoping we had seen our last tropical threat of the season.  There was another forming down in the Caribbean again (which became Iota, a record-breaking 30th this year) but the long-term models did not predict a northern trek in our direction.  Eventually Iota spun up into a Cat-5 and clobbered the same areas of Nicaragua and Guatemala that had been whacked by Eta on its first landfall two weeks prior.  We count our blessings. 

Break/Fix 

Nothing broke this month.  Honest.  Really. 

Regular Maintenance 

It was a light month overall, and apart from the humdrum repetition of numerous, minor Wheelhouse preventive tasks, the main task this month was the bi-annual coolant flush for the wing engine.  In addition to serving as our “get home” auxiliary propulsion unit, that Lugger 984 also powers the hydraulics for our bow and stern thrusters, in addition to the Maxwell 3500 windlass.  It’s almost as important at the main engine, so we pay attention to its care and feeding requirements. 

But unlike the generator and main engine diesels, we had never tackled a coolant system flush for that powerplant – our friends at Yacht Tech had handled the last one two years ago.  Still, the principles were the same, so after a review of the technical manuals, Rick went after it.  Overall it was pretty straightforward, with the main key being the use of the flexible “Form-a-Funnel” – actually two of them; otherwise we would have ended up with all the coolant in the bilge instead of a drain bucket.  After that we flushed with fresh water until the drain ran clear and replaced the drain plug. 

Form-a-Funnels Make Draining Coolant a Much More Precision Operation

While he was at it, Rick also attacked a thorough cleaning of the heat exchanger core, and even that turned out to be reasonably easy:  remove the pencil zinc and drain plug, then both cap ends, take a wire rod and router it into each of the many honeycomb passages, pick out the old pieces of sacrificial zincs, and slap it all back together with a new pencil zinc. 

End Cap Removed on One End of the Heat Exchanger

After adding back about three gallons of the Peak Fleet Charge 50/50 premix (the Luggers are picky about their coolant), the engine checked out under load with no leaks, and kept a steady 180F on the temp gauge.  

Project Work 

There was only one small project that we got to this month, and that was the annual detailing of the dinghy.  To say the dinghy was dingy doesn’t quite cover it.  Cleaning and waxing of the interior FRP surfaces was fairly straightforward, but scrubbing the Hypalon inflatable tubes took several passes with different cleaning solutions before it was anywhere close to acceptable. 

Final (?) Tropical Weather Check 

Almost December & the Tropics Aren't Done Yet

The official hurricane season runs from 01-June to 30-November.  That’s actually an arbitrary definition that simply brackets the months in which most tropical systems (about 97%) have historically formed.  But there isn’t a month when a tropical weather system has not formed.   After Hurricane Eta we were hoping we were done with them for this year, but then the day after the US Thanksgiving holiday two more areas got flagged for potential development.  Fortunately neither were anywhere close to us. 

Departing the Boat 

And lastly, the reconstruction efforts at the condo progressed far enough to make it sufficiently livable.  Chelle had actually been spending more time there than on the boat – busy with project oversight and numerous complementary projects that dovetailed with the overall renovation scheme – while Rick had made a conscious effort to avoid most of the mayhem, enjoying the quiet of the boat.  But by the time the Thanksgiving holiday rolled around most of the major work had been completed, and we both returned to dirt-dwelling. 

The Major Renovation Work Progressed Enough to Allow a Thanksgiving Back at the Condo

Finally, a big thanks to our friends Martin and Stephanie Maurer aboard N60, Blossom, who stopped off at Legacy Harbour on their way from RFYC to their home in St. Petersburgh.   They hosted us for two enjoyable evenings in the spacious open-air cockpit of Blossom, and the rare social experience was a wonderful break from the rigors of the pandemic. 

With the arrival of December and south Florida’s version of winter, we’re now at a point where we may start contemplating what Rick calls “a different kind of boat.”  But that’s an evaluation still in the very early stages, with more to come in the future.  Stay tuned. 

Afterword:  During any crisis the only thing more dangerous than a leadership void is blaming conspiracy theories for those failures of leadership.  That’s a downward spiral from which the weak-minded never functionally recover.  And from which pandemic victims get sick or die.  We’re supposed to be better than this, but unlike previous generations, too many are proving they are not up to the challenges.

Wednesday, November 4, 2020

October 2020: Back on the Boat

Coping with Covid can often feel like déjà vu….as in, what day is it?  It’s today.  Still.  It’s like a really bad version of the movie Groundhog Day, but with annoying masks, no hugs, and a pathetic plot.  Rick gave up on remembering days of the week and now calls each day “Blursday.”

View of the Portion of the Condo Where Kitchen & Wall &
Floor Tile Were All Ripped Out

Chelle got so bored she decided to demolish about half of our condo as a distraction. Presumably that was in preparation for a remodeling effort, and Rick evacuated to the boat just before the jack hammering started.  That turned out to be good timing as we had a lot going on in terms of Ghost Rider activity.

Break/Fix

Rick had invited Craig of VIP Marine out to the boat to evaluate a cooling problem with the A/C unit for the pilot house.  That’s a relatively new compressor/evaporator combination (barely two years old) but its cooling output was trending 10F warmer than all the other units.  That’s enough deficit to greatly impact the pilot house with all its greenhouse-like glass.  Craig showed up on day one of the condo exodus and slapped the gauges on the suspect compressor.  That revealed a lack of refrigerant pressure and volume, so he pumped it up with the R410A stuff, providing an immediate improvement.  We did not find any leaks in the obvious plumbing places, so we’ll run it for a while in the south Florida swelter and see how it holds up over time.

Jerry & Ross Trying to Figure Out How to Fit the New HPU
Assembly into the Too-Small Space in the Base

At about the same time Ross and Jerry of Class Yacht Services showed up with the heavily altered HPU for the davit/crane.  The machine shop mods to the fastener holes, fluid ports and hydraulic adaptors still allowed installation room in the base of the davit, but it was a very tight fit.  Sleuthing the electrical connections took a while as we did not have the benefit of a good schematic, but Ross was able to cobble together a reverse engineering of the wiring.  New hydraulic hoses were then fashioned and connected.  All that took a few days.

Then it was time to add hydraulic fluid (about two gallons of ISO 68), apply power through the circuit breaker, connect the control pendant and test it all out.  We got good movement of the hook up and down, and of the boom to port, starboard, and down – but it would not raise.  Suspecting that particular control valve had a blockage in the “up” direction, they again removed the valve manifold and took it to the shop for individual valve testing.  Some debris was found and removed but upon reassembly back at the boat we still faced the same problem.

So, we all stood there and stared at the crane for a while, waiting for some inspiration.  It came to Jerry:  while the motor would run with the “boom up” command the valve might not be opening via the magnetic coil actuation, or in other words, it was an electrical issue. We had previously requested an updated wiring schematic for this later version HPU from the manufacturer (Aritex) in Taiwan, but had received no response.  Revisiting the control box wiring with a Fluke volt meter eventually led to the discovery of a well-hidden orphan ground wire.  Once it was connected, we were back in business.  The final touch was for Rick to clean and polish the base, and to drill an additional drain hole at the rear of the davit’s base.

This is How the New HPU Assembly Looked Before We Turned it Over to the Machine Shop
for Some Significant Modifications

The Machine Shop Removed the Valve Manifold Assembly and Crafted a New Mounting Base
So That it Could be Installed Off to the Side of the HPU

In Place of Where the Valve Manifold Used to be, the Machine Shop Created a New and
Smaller Interface Block to Mate with the Relocated "Remote" Valve Manifold

Regular Maintenance

It was also time for Ghost Rider to get her periodic spa treatment.  Based just on visual evidence she was actually overdue – while the light gray vertical hull surfaces below the gunwales still looked pretty good, after 11 months the white FRP surfaces above that were getting that dull weathered look.   And keeping it clean was becoming a real chore.

The Bow of Ghost Rider Getting Detailed

We engaged Frank of Ultimate Marine (LINK) once again to tackle the enormous job of washing and waxing the entirety of the boat’s exterior.  Over a period of six days he and a few helpers got Ghost Rider looking spiffy once again, with the aid of electric buffers and copious amounts of Collonite Fleetwax on the FRP and Flitz on the brightwork.

Next up was the bi-annual service for Ghost Rider’s two Vacuflush toilets.  We had been experiencing minor and periodic issues with a temperamental water valve on one of them, along with a slow vacuum leak on the other, so Rick lobbed a call to the local Dometic shop. Travis and Gary from Fleet Repair (LINK) tore down and replaced the key serviceable parts for both heads, and also serviced the two vacuum pumps with motor mount adjustments and new duckbill valves.  It’s always good to have a smoothly operating waste water system.

Ghost Rider Looked a Lot Better After Frank & His Crew Finished Up

Project Work

Rick focused on a short list of “little stuff” this month….touching up paint scars in the engine room, refreshing Denso tape wraps on some hydraulic fittings, polishing corrosion from the pilot house Stidd chair base, and drilling a new drain hole for a fly bridge storage box.  The gas tank and spare gas cans for the dinghy also got reinforcing shots of Sta-Bil fuel conditioner – that stuff loses its potency after about a year. The overall punch list actually – finally – got a tad shorter this month.

Rick Got Some Cleaning & Detailing Work Done in the Engine Room, Too

The Steering Box & Stern Thruster Hydraulic Manifold in the Lazarette....Along with the Bow
Thruster Compartment, It Also Got Cleaned Up and New Denso Tape Wraps

Tropical Weather Check!

Hurricane Epsilon spun up into a major storm but fortunately stayed out in the open Atlantic, even missing Bermuda (barely) as it curved away from the U.S. and far to the northeast.  Then, as expected, yet another tropical system spooled up in the Caribbean this month and eventually made its way into the Gulf of Mexico.  Now deep into the Greek alphabet names, Hurricane Zeta got steered away from us by a high pressure system to our east and took initial aim at the Yucatan.  And then, following a disturbing pattern this season, once again the Louisiana coastline was bore sighted.  It would be their fifth of 2020.

After Five of These We're Guessing Land in Louisiana & Mississippi is Getting Pretty Cheap

As October came to a close yet another system was just spinning up, and didn’t take TD29 very long to morph into Tropical Storm Eta.  It was forecast to ping pong around the Caribbean before potentially turning north towards us….but as you can tell from the scattered model plots in the graphic below, they really have no clue where this one would end up going.  We’ll be monitoring closely.

The Early Track Forecasts for the Next Storm are Literally All Over the Place

And finally, to bring October to a proper close, we enjoyed a marina-style celebration of Halloween.  By 31-October our temps had moderated to a pleasant 80F, with a pleasant breeze and mostly clear skies. That allowed B-dock adults to gather for happy hour docktails, and then at sunset the youngsters in our little liveaboard community enjoyed a fun, albeit masked and socially distanced “Trick-or-Treat” experience.

Trick-or-Treating on the Docks at Legacy Harbour Marina

Afterword: As we went to press with this blog entry the latest tally of the US election results was still underway.  One candidate was lobbying to stop counting votes and declare himself the winner.  We suppose there's something to be said for being a consistent cheat.  Meanwhile the virus seemed to be exploding (again) nearly everywhere.  Be very careful out there.